Power supply - MINI-SYS-PS-100-240AC/24DC/1.5 2866983

Primary-switched MINI POWER supply for DIN rail mounting, input: 1-phase, output: 24 V DC/1.5 A

Detalii despre produs


MINI POWER power supplies for MCR technology
In measurement and control technology (MCR), modular electronics housing has become the industry standard. MINI POWER is the power supply unit to go with it. The devices are flexible, thanks to special voltages and special versions.



Efficiency > 84 % (for 230 V AC and nominal values)
Output characteristic U/I
Nominal output voltage 24 V DC ±1 %
Nominal output current (IN) 1.5 A (-25 °C ... 60 °C)
Output current limit 7 A (in the event of a short-circuit)
POWER BOOST (IBoost) 2 A (-25°C ... 40°C permanent )
Derating 60 °C ... 70 °C (2.5%/K)
Feedback voltage resistance 35 V DC
Protection against overvoltage at the output (OVP) < 30 V DC
Max. capacitive load unlimited
Control deviation < 1 % (change in load, static 10 % ... 90 %)
Control deviation < 3 % (change in load, dynamic 10 % ... 90 %)
Control deviation < 0.1 % (change in input voltage ±10 %)
Residual ripple < 40 mVPP (20 MHz)
Short-circuit-proof yes
Output power 36 W
Peak switching voltages idling < 20 mVPP (20 MHz)
Peak switching voltages nominal load < 20 mVPP (20 MHz)
Maximum power dissipation in no-load condition 1.5 W
Power loss nominal load max. 6.5 W
Rise time < 2 ms
Connection in parallel Yes, for redundancy and increased capacity.
Maximum of 2 devices for redundancy on DIN rail connector.
Connection in series No
Signal: DC OK floating
Output description UOUT > 21.5 V: Contact closed
Maximum switching voltage ≤ 30 V AC/DC
Output voltage 30 V AC/DC
Continuous load current ≤ 1 A

Nominal input voltage range 100 V AC ... 240 V AC
Input voltage range 85 V AC ... 264 V AC
Input voltage range
Input voltage range AC 85 V AC ... 264 V AC
Voltage type of supply voltage AC
Inrush current < 15 A (0.6 A2s)
Inrush current integral (I2t) 0.6 A2s
AC frequency range 45 Hz ... 65 Hz
Mains buffering time typ. 35 ms (120 V AC)
Mains buffering time typ. 150 ms (230 V AC)
Current consumption 0.75 A (120 V AC)
Current consumption 0.45 A (230 V AC)
Nominal power consumption 90 VA
Protective circuit Transient surge protection; Varistor
Typical response time < 0.5 s
Input fuse 3.15 A (slow-blow, internal)
Permissible backup fuse B6 B10 B16
Recommended breaker for input protection 6 A ... 16 A (Characteristics B, C, D, K)

Environmental Product Compliance
REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 25;
China RoHS For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration”

Insulation voltage input/output 4 kV (type test)
Insulation voltage input/output 3 kV (routine test)

Width 35 mm
Height 99 mm
Depth 95 mm
Installation dimensions
Installation distance right/left 0 mm / 0 mm
Installation distance top/bottom 50 mm / 50 mm

Types of signaling LED
Types of signaling Relay contact
Operating voltage display Green LED
Signal output: DC OK floating
Status display "DC OK" LED green
Note on status display UOUT > 21.5 V: LED lights up

Color green
Type of housing Polyamide PA, color: green

Mounting type DIN rail mounting
Assembly instructions alignable: horizontally 0 mm, vertically 50 mm
Mounting position horizontal DIN rail NS 35, EN 60715

UL approvals UL/C-UL listed UL 508
UL approvals UL/C-UL Recognized UL 60950-1
UL approvals UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D (Hazardous Location)
Conformity/Approvals
SIL in accordance with IEC 61508 0
Performance level according to ISO 13849 without

Low Voltage Directive Conformance with Low Voltage Directive 2014/35/EC
Electromagnetic compatibility Conformance with EMC Directive 2014/30/EU
EMC requirements for noise emission EN 61000-6-3
EMC requirements for noise emission EN 61000-6-4
EMC requirements for noise immunity EN 61000-6-1
EMC requirements for noise immunity EN 61000-6-2
Noise emission EN 55011 (EN 55022)
Noise immunity EN 61000-6-2:2005
Fast transients (burst)
Standards/regulations EN 61000-4-4
Input 4 kV (level 4 - asymmetrical: conductor to ground)
Output 2 kV (level 3 - asymmetrical: conductor to ground)
Signal 1 kV (level 2 - asymmetrical: conductor to ground)
Comments Criterion B
Conducted interference
Standards/regulations EN 61000-4-6
I/O/S Level 3 - asymmetrical
Frequency range 0.15 MHz ... 80 MHz
Comments Criterion A
Voltage 10 V
Electromagnetic HF field
Standards/regulations EN 61000-4-3
Frequency range 80 MHz ... 2 GHz
Test field strength 10 V/m
Comments Criterion A
Surge voltage load (surge)
Standards/regulations EN 61000-4-5
Electrostatic discharge
Standards/regulations EN 61000-4-2
Housing Level 3
Contact discharge 6 kV
Discharge in air 8 kV
Comments Criterion B
Emitted interference
Standards/regulations EN 61000-6-3
Radio interference voltage in acc. with EN 55011 EN 55011 (EN 55022) Class B, area of application: Industry and residential
Emitted radio interference in acc. with EN 55011 EN 55011 (EN 55022) Class B, area of application: Industry and residential
Voltage dips
Standards/regulations EN 61000-4-11

Degree of protection IP20
Ambient temperature (operation) -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Ambient temperature (storage/transport) -40 °C ... 85 °C
Climatic class 3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation) ≤ 95 % (at 25 °C, non-condensing)
Shock 18 ms, 30g, in each space direction (according to IEC 60068-2-27)
Vibration (operation) < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6)
Vibration (operation) 15 Hz ... 150 Hz, 2.3g, 90 min.

Test socket torque
Signal
Conductor cross section solid min. 0.2 mm2
Conductor cross section solid max. 2.5 mm2
Conductor cross section flexible min. 0.2 mm2
Conductor cross section flexible max. 2.5 mm2
Conductor cross section AWG min. 24
Conductor cross section AWG max. 12
Screw thread M3
Tightening torque, min 0.5 Nm
Tightening torque max 0.6 Nm
Input
Connection method Pluggable screw connection
Conductor cross section solid min. 0.2 mm2
Conductor cross section solid max. 2.5 mm2
Conductor cross section flexible min. 0.2 mm2
Conductor cross section flexible max. 2.5 mm2
Conductor cross section AWG min. 24
Conductor cross section AWG max. 12
Stripping length 7 mm
Screw thread M3
Tightening torque, min 0.5 Nm
Tightening torque max 0.6 Nm
Output
Connection method Pluggable screw connection
Conductor cross section solid min. 0.2 mm2
Conductor cross section solid max. 2.5 mm2
Conductor cross section flexible min. 0.2 mm2
Conductor cross section flexible max. 2.5 mm2
Conductor cross section AWG min. 24
Conductor cross section AWG max. 12
Stripping length 7 mm
Screw thread M3
Tightening torque, min 0.5 Nm
Tightening torque max 0.6 Nm

Rail applications EN 50121-4
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations EN 50178/VDE 0160 (PELV)
Standard – Limitation of mains harmonic currents EN 61000-3-2
Standard - Electrical safety EN 60950-1/VDE 0805 (SELV)
Standard – Safety extra-low voltage EN 60950-1 (SELV) and EN 60204 (PELV)
Standard – Safety extra-low voltage EN 60204 (PELV)
Standard - Safe isolation DIN VDE 0100-410

MTBF (IEC 61709, SN 29500) > 2789000 h (40 °C)
Insulation characteristics
Protection class II (in closed control cabinet)
Overvoltage category III
Degree of pollution 2


Cod comandă 2866983
Unitate de ambalare 1 pc
Cantitate minimă pentru comandă 1 pc
Pagina de catalog Pagina 276 (C-4-2019)
GTIN 4017918960650
Greutate pe bucată (inclusiv ambalajul) 288,0 GRM
Greutate pe bucată (fără ambalaj) 250,0 GRM
Cod tarifar vamal 85044030
Țara de origine CN



UL Listed

UL Recognized

cUL Recognized

cUL Listed

EAC

EAC

cULus Recognized

cULus Listed

cULus Listed

UL Listed

cUL Listed


Avantajele dumneavoastră

Easy-maintenance connection technology thanks to keyed COMBICON connectors
Status and error indication via diagnostic LEDs
For supplying the supply voltage via the foot element (DIN rail connector) where AC voltages are available
100 ... 240 V AC nominal input voltage range
24 V DC output voltage
For up to 60 MINI Analog modules
For up to 1.5 A, secondary