Network cable - VS-FSBPYS-OE-94H/1,5 SCO
1412467

Hybrid flush-type socket, Ethernet, 8-pos., M12-SPEEDCON, rear/screw mounting with M16 thread, 360° shield connection with connected shielded hybrid cable


Detalii despre produs




Notes on operation The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product type Circular connectors (device side)
Number of positions 8
Coding Y - hybrid
Insulation characteristics
Overvoltage category II
Degree of pollution 3

Degree of protection IP67
Degree of protection IP65/IP67
Ambient temperature (operation) -25 °C ... 80 °C (Plug / socket)
-40 °C ... 80 °C (without mechanical actuation)

Insertion/withdrawal cycles ≥ 100
Header 1
Head design Flush-type female connector
Head cable outlet straight
Head thread type M12
Head locking type SPEEDCON
Coding Y - hybrid
Head 2
Head design free cable end

Contact resistance ≤ 3 mΩ
Insulation resistance ≥ 100 MΩ
Nominal voltage UN 48 V AC (Power and data)
50 V DC (Power and data)
Nominal current IN 0.5 A (Data)
6 A (Power)
Transmission medium Copper

Material Zinc die-cast (nickel-plated)
Flammability rating according to UL 94 V0
Sealing material FKM
Contact material CuZn
Contact surface material Ni/Au
Contact carrier material PA 6.6
Cable gland material Nickel-plated brass

Connection technology
Connection method Hybrid cable
Conductor connection
Connection method Hybrid cable

Mounting type Rear mounting

M12
Standards/specifications IEC 61076-2-113

Cable structure
Signal type/category Ethernet hybrid CAT5 (IEC 11801:2002), 100 Mbps

Număr articol 1412467
Unitate de ambalare 1 Bucată
Cantitate minimă pentru comandă 30 Bucată
Indicație Produs la comandă (nereturnabil)
Cod produs ABQCED
GTIN 4046356965453
Greutate pe bucată (inclusiv ambalajul) 161,7 g
Greutate pe bucată (fără ambalaj) 158,3 g
Cod tarifar vamal 85444290
Țara de origine DE


ECLASS

ECLASS-9.0 27141137
ECLASS-10.0.1 27141137
ECLASS-11.0 27281101

ETIM

ETIM 8.0 EC000761

UNSPSC

UNSPSC 21.0

cUL Recognized

UL Recognized

EAC

cULus Recognized


REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Avantajele dumneavoastră

Pre-assembled with cables in various standard lengths for immediate use
Customer-specific assemblies and cable lengths can be supplied
Sealed on the cable side for optimum tightness of seal
Cable designs for all common networks and fieldbuses
For high transmission safety: shield connection to the housing with optional EMC nut