Connector in molded plastic on both sides - K-3E-M23 M9/010-A00/M23 F8

Connector in molded plastic on both sides, length: 10 m, color of outer sheath: gray RAL 7001

Detalhes dos produtos

Notes on operation Observe derating curve.
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at must be observed for this product.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product type Signal and power cable

Cable length 10 m

N.º de artigo 1624774
Pcs./Emb 1 Unidade
Quantidade mínima de pedido 2 Unidade
Observação Produção ligada a pedido (sem devolução)
Chave comercial ABR
Chave de produto ABRDFE
Página de catálogo Página 220 (C-2-2019)
GTIN 4046356639194
Peso por unidade (inclusive embalagem) 3 107 g
Peso por unidade (excluindo embalagem) 3 107 g
Número do imposto alfandegário 85444290
País de origem DE


ECLASS-9.0 27062011
ECLASS-10.0.1 27060106
ECLASS-11.0 27060106


ETIM 8.0 EC003250


UNSPSC 21.0 26121600


UL Listed

Approval Specification Data
Tensão nominal UN Corrente nominal IN Secção transversal American Wire Gauge Secção transversal mm2
Power 600 V 25 A

cUL Listed

Approval Specification Data
Tensão nominal UN Corrente nominal IN Secção transversal American Wire Gauge Secção transversal mm2
Power 600 V 25 A

cULus Listed

REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”


Our standard: robust halogen-free PUR cable
Simple and safe: 100% electrically tested and assembled ready for use
Designs with pre-assembled cables on one or both sides
High flexibility: customer-specific assemblies and cable lengths can be supplied