Device connector, front mounting - PV-FT-CM-C-6-350-BK
1806037

Panel feed-through, Range of articles: Sunclix, Device connector, front mounting, housing material: PPE, color: black, number of positions: 1, min. conductor cross section: 6 mm2, Connection method: Crimp, Type of contact: Pin, cable length: 350


Detalhes dos produtos




Safety note
Safety note • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.

Product type Panel feed-through
Number of positions 1
Locking type Latching (can only be released using tool)
Insertion force 45 N ±10 N
Insulation characteristics
Protection class II
Degree of pollution 2

Desenho cotado
Width 26.3 mm
Height 26.3 mm
Length 41.5 mm

Rated voltage (III/2) 1000 V
Rated surge voltage (III/2) 12 kV
Rated current (6.0 mm²) 40 A
Contact resistance 0.45 mΩ
Contact resistance ≤ 0.45 mΩ (when plugged in (without cable))

Mechanical data
Insertion force 45 N ±10 N
Withdrawal force 250 N ±50 N (when locked)

Color black
Color of the housing part black
Flammability rating according to UL 94 V0
Insulating material group III
Seal material EPDM
Insulating material mPPE
Contact surface Silver Ag
Cable seal material Elastosil LR 3065/50
Contact material Cu
Contact surface material Ag
Contact carrier material PPE
Housing material PPE

Insertion/withdrawal cycles 100

Cable length 350 mm
Cable structure
Structure of individual litz in acc. with VDE 0295 / smallest wire diameter 84x0.3
Cable type Railway cable
Cable type Railway cable Radox GKW-S
Cable structure tin-plated, fine-wired, IEC 60228 Class 5
External cable diameter 5.4 mm ±0.15 mm
5.1 mm 4.95 mm 5.25 mm ±0.15 mm
Outer sheath, material PE-X
External sheath, color black
Single wire, material Cu
Single wire, cross section 6 mm²
Mechanical properties
Smallest bending radius, fixed installation 10.2 mm (2x Ø)
Smallest bending radius, movable installation 15.3 mm (3x Ø)
Cable pull-out force > 80 N
Bending cycles
Smallest bending radius, fixed installation 10.2 mm (2x Ø)
Smallest bending radius, movable installation 15.3 mm (3x Ø)
Ambient conditions
Halogen-free yes
Resistance to oil yes
Flame resistance yes

Degree of protection (when plugged in) IP66 / IP68 (2 m / 24 h)
Degree of protection (not plugged in) IP20
Degree of protection IP66 / IP68 (2 m / 24 h)
Ambient temperature (operation) -40 °C ... 85 °C
Ambient temperature (assembly) -25 °C ... 50 °C
Resistance to oil yes

Flame resistance yes
Resistance to oil yes

N.º de artigo 1806037
Pcs./Emb 50 Unidade
Quantidade mínima de pedido 50 Unidade
Observação Produção ligada a pedido (sem devolução)
Chave comercial ABL
Chave de produto ABLBAA
GTIN 4046356688949
Peso por unidade (inclusive embalagem) 33,63 g
Peso por unidade (excluindo embalagem) 33,63 g
Número do imposto alfandegário 85444290
País de origem DE


ECLASS

ECLASS-9.0 27440107
ECLASS-10.0.1 27440107
ECLASS-11.0 27440107

ETIM

ETIM 8.0 EC002635

UNSPSC

UNSPSC 21.0

EAC

Approval ID: B.01687

TÜV Rheinland

Approval ID: R 60126961
Approval Specification Data
Tensão nominal UN Corrente nominal IN Secção transversal American Wire Gauge Secção transversal mm2
1500 V

China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values