SM-5EPWN8AWT00 - Device connector front mounting

1613517

Device connector front mounting, straight, for standard and SPEEDCON interlock, M40, number of positions: 2+3+PE, contact connection type: Pin, Axial O-ring, shielded: yes, flange dimensions: 40 mm x 40 mm, number of positions: 6, connection method: Crimp connection, series: SM, this item is expected to be lead-free from Q2 2026 in accordance with RoHS II without exception 6c (Pb < 0.1%), a lead-free alternative is possible on request in advance

Detalhes dos produtos

Order information:	Order crimp contacts 2 x Ø 2 mm, 4 x Ø 3.6 mm separately
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
	• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
	• The products are suitable for applications in plant, controller, and electrical device engineering.
	• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
	• Assembled products may not be manipulated or improperly opened.
	• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
	• When using the product in direct connection with third-party manufacturers, the user is responsible.
	• For operating voltages > 50 V AC, conductive connector housings must be grounded
	• Ensure that the protective or functional ground has been properly connected.
	• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
	• Only use tools recommended by Phoenix Contact
	• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
	• Operate the connector only when it is fully plugged in and interlocked.
	• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
	• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
	• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Mounting type	Front mounting/square flange (4x Ø 4,2 mm)

Product type	Circular connectors (device side)
Series	SM
Application	Power
Number of positions	6
Connection profile	2+3+PE
Shielded	yes
Coding	N
Thread type	M40

Housing
Flange dimensions	40 mm x 40 mm

Material Housing	GD-Zn
Material Rotating parts	CuZn
Material Housing surface	Ni
Material Insulating body	PA 6.6
Material Seal	FPM (O-ring)

Contact: Contact group 1
Contact diameter	3.6 mm
Nominal current I_N	70 A
Nominal voltage U_N	630 V
Overvoltage category	III
Degree of pollution	3
Rated surge voltage	6 kV
Contact: Contact group 2
Contact diameter	2 mm
Nominal current I_N	30 A
Nominal voltage U_N	250 V
Overvoltage category	III
Degree of pollution	3
Rated surge voltage	4 kV

Conductor connection
Connection method	Crimp connection
Contact connection type	Pin

Type	straight

Ambient conditions
Degree of protection	IP67
Ambient temperature (operation)	-40 °C ... 125 °C
Altitude	3000 m

Dados comerciais

N.º de artigo	1613517
Pcs./Emb	1 Unidade
Quantidade mínima de pedido	1 Unidade
Chave comercial	ABR
Chave de produto	ABRBGL
GTIN	4046356364829
Peso por unidade (inclusive embalagem)	190,3 g
Peso por unidade (excluindo embalagem)	127,837 g
Número do imposto alfandegário	85366990
País de origem	DE

Classificações

Certificações

Approval Specification Data
	Tensão nominal U_N	Corrente nominal I_N
keine
Power	600 V	40 A
Signal	600 V	20 A

Approval Specification Data
	Tensão nominal U_N	Corrente nominal I_N
keine
Power	600 V	65 A
Signal	600 V	30 A

Environmental product compliance

Produtos compatíveis

Acessórios

Vantagens

Consistent EMC protection for reliable connection solutions in the industrial environment

Crimping connection: vibration- and temperature-resistant assembly

Phoenix Contact S.A.

Sintra Business Park, Edifício n°1 Zona Industrial da Abrunheira, sala 0M, 2710-089 SINTRA

Fazer uma pergunta (+351) 21 911 2760 pt-info@phoenixcontact.com

ECLASS-13.0	27440109
ECLASS-15.0	27440109

EU RoHS
Cumpre os requisitos de substância segundo a Diretiva RoHS	Sim
isenções tanto quanto conhecido	6(c)
China RoHS
Environment friendly use period (EFUP)	EFUP-50 Uma lista de declaração de acordo com a RoHS da China relativa a artigos encontra-se na área de transferências do respetivo artigo, em "Declaração do fabricante". Para todos os artigos com EFUP-E não é emitida nem necessária uma tabela de declaração de acordo com a RoHS da China.
EU REACH SVHC
Nota sobre as substâncias candidatas ao REACH (n.º CAS)	Lead (n.º CAS: 7439-92-1)
SCIP	d79d30c8-dcc5-4e79-8a7b-fc7a2857731a

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

SM-5EPWN8AWT00 - Device connector front mounting

1613517

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

cUL Recognized

UL Recognized

Produtos compatíveis

Vantagens

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

SM-5EPWN8AWT00 - Device connector front mounting 1613517

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

Produtos compatíveis

SM-36KP001 - Crimp contact 1605743

SM-36KP009 - Crimp contact 1607057

SM-36KP002 - Crimp contact 1605744

SM-36KP003 - Crimp contact 1605745

SM-36KP004 - Crimp contact 1605747

SF-7RP2000 - Crimp contact 1605646

SF-7PP2000 - Crimp contact 1605634

SF-20KP004 - Crimp contact 1607376

SF-7QP2000 - Crimp contact 1605639

SF-7MP2000 - Crimp contact 1605626

SM-Z0028 - Color coding 1620627

SM-Z0029 - Color coding 1620628

SM-Z0030 - Color coding 1620629

SB-Z0001 - Metal protective cap 1623827

PROT-M40-PW-OT-IP20 - Plastic protective cap 1577212

Vantagens

Pesquisado com frequência

SM-5EPWN8AWT00 - Device connector front mounting

1613517