D-SUB bus connector - SUBCON-PLUS-CAN/PG - 2708119

D-SUB connector, 9-pos. socket, cable entry < 35°, bus system: CAN, CANopen®, SafetyBUS p up to 1 Mbps, with PG D-SUB socket for connecting a programming device, termination resistor can be switched on via slide switch, pin assignment: 2, 3, 7, 9; screw terminal blocks

Price:

Overview

Technical data

Accessories

Approvals

Downloads

Drawings



Dimensional drawing  

Dimensional drawing

Circuit diagram  

Circuit diagram



Schematic diagram  

Schematic diagram
1 Upper housing part
2 Slide switch
3 BUS IN connection block
4 BUS OUT connection block
5 UNC mounting screw
6 Lower housing part
7 Strain relief
8 PG connection
9 Housing screw

Back to top

Note

Utilization restriction Use in potentially explosive areas is not permitted in China.
Back to top

Dimensions

Max. cable diameter 8.4 mm
Min. cable diameter 7.6 mm
Width 16.6 mm
Height 39.4 mm
Length 58 mm
Back to top

Ambient conditions

Ambient temperature (operation) -20 °C ... 75 °C
Ambient temperature (storage/transport) -25 °C ... 80 °C
Altitude ≤ 5000 m (For restrictions, see the manufacturer's declaration for altitude operation)
Degree of protection IP40
Back to top

General

Nominal voltage UN 5 V
Nominal current IN 100 mA
Bus system CAN, CANopen, SafetyBus-P
Signal CAN
CANopen®
SafetyBUS p
Insertion/withdrawal cycles > 200
SUBCON fixing screws 4-40 UNC
Tightening torque 0.4 Nm
Housing material ABS, metal-plated
Pin assignment 2, 3, 7, 9
MTTF 6706 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
1817 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%)
155 Years (SN 29500 standard, temperature 40°C, operating cycle 100%)
Back to top

Connection data

Connection D-SUB connection
Number of positions 9
Connection method D-SUB connector
Termination resistor 120 Ω (Can be connected externally)
Connection PCB connection
Connection method Screw connection
Conductor cross section flexible min. 0.14 mm²
Conductor cross section flexible max. 1 mm²
Conductor cross section solid min. 0.14 mm²
Conductor cross section solid max. 1.5 mm²
Min. AWG conductor cross section, flexible 26
Max. AWG conductor cross section, flexible 18
Conductor cross section AWG min. 26
Conductor cross section AWG max. 16
Stripping length 5 mm
Tightening torque 0.4 Nm
Connection Programming connection
Number of positions 9
Connection method D-SUB connector
Back to top

Conformance/approvals

Designation EAC
Identification EAC
Designation ATEX
Identification  II 3 G Ex nA IIC T4 Gc X
Additional text Please follow the special installation instructions in the documentation!
Designation Corrosive gas test
Identification ISA-S71.04-1985 G3 Harsh Group A
Back to top

Standards and Regulations

Free from substances that could impair the application of coating according to P-VW 3.10.7 57 65 0 VW-AUDI-Seat central standard
Connection in acc. with standard CUL
Back to top

Environmental Product Compliance

REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration”
Back to top

Classifications

eCl@ss

eCl@ss 10.0.1 27440302
eCl@ss 11.0 27440302
eCl@ss 4.0 27140800
eCl@ss 4.1 27140800
eCl@ss 5.0 27143400
eCl@ss 5.1 27143400
eCl@ss 6.0 27143400
eCl@ss 7.0 27440302
eCl@ss 8.0 27440302
eCl@ss 9.0 27440302
Back to top

ETIM

ETIM 2.0 EC001132
ETIM 3.0 EC001132
ETIM 4.0 EC001132
ETIM 5.0 EC001132
ETIM 6.0 EC001132
ETIM 7.0 EC001132
Back to top

UNSPSC

UNSPSC 6.01 30211802
UNSPSC 7.0901 39121402
UNSPSC 11 39121402
UNSPSC 12.01 39121402
UNSPSC 13.2 39121522
UNSPSC 18.0 39121522
UNSPSC 19.0 39121522
UNSPSC 20.0 39121522
UNSPSC 21.0 39121522
Back to top

PHOENIX CONTACT (Pty) Ltd.

36 Lyn Road
P.O. Box 916
ZA-Ferndale 2160
+27/11/801-8200

  • Create PDF
  • Recommend
  • Feedback