Sleeve housing - VC-K-T1-R - 1855092

Sleeve housings, Sleeve housing, type: VC1, housing material: PA 6, color: gray. When using fiber optics, the bending radii of the cable manufacturers must be observed.


Save money: Best price starts from {0} pieces!


Technical data





Dimensional drawing  

Dimensional drawing

Dimensional drawing  

Dimensional drawing

Dimensional drawing  

Dimensional drawing

Product drawing  

Product drawing

Back to top


Height 66 mm
Back to top

Ambient conditions

Degree of protection IP67
Ambient temperature (operation) -40 °C ... 80 °C
Back to top


Note When using fiber optics, the bending radii of the cable manufacturers must be observed.
Type VC1
Degree of protection IP67
Flammability rating according to UL 94 V0
Locking type Screw locking, knurled head
Fixing screws M4
Tightening torque, mounting screw 1.5 Nm ±0.3 Nm
Type of the screw connection Pg16
Cable outlet angled
Housing material PA 6
Seal material EPDM
Ambient temperature (operation) -40 °C ... 80 °C
Back to top

Standards and Regulations

Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Back to top

Environmental Product Compliance

China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values
Back to top



ECLASS 10.0.1 27440202
ECLASS 11.0 27440202
ECLASS 4.0 27140800
ECLASS 4.1 27140800
ECLASS 5.0 27371200
ECLASS 5.1 27261200
ECLASS 6.0 27261200
ECLASS 7.0 27440202
ECLASS 9.0 27440202
Back to top


ETIM 2.0 EC000437
ETIM 3.0 EC000437
ETIM 4.0 EC000437
ETIM 6.0 EC000437
ETIM 7.0 EC000437
Back to top


UNSPSC 6.01 31261501
UNSPSC 7.0901 31261501
UNSPSC 11 31261501
UNSPSC 12.01 31261501
UNSPSC 13.2 31261501
UNSPSC 18.0 31261501
UNSPSC 19.0 31261501
UNSPSC 20.0 31261501
UNSPSC 21.0 31261501
Back to top


586 Fulling Mill Road
Middletown, PA 17057
(800) 888-7388

  • Create PDF
  • Send by Email
  • Feedback