Contact insert - VC-D2-BU30-PE - 1855063

Contact insert, Range of articles: VARIOCON, Contact insert, type: VC2, housing material: PA, number of positions: 30, min. conductor cross section: 0.14 mm², max. conductor cross section: 1.5 mm², Connection method: Crimp connection, Type of contact: Socket. Connectors may only be connected/disconnected when under no load.

Price:

Save money: Best price starts from {0} pieces!

Overview

Technical data

Accessories

Approvals

Downloads

Drawings



Dimensional drawing  

Dimensional drawing
Contact insert

Dimensional drawing  

Dimensional drawing
Mounting cutout



Back to top

Electrical characteristics

Rated voltage (III/3) 250 V
250 V
Rated current 10 A
10 A
Rated surge voltage 4 kV
Rated surge voltage (II/2) 2.5 kV
Rated surge voltage (III/2) 4 kV
Connection profile 30+PE
Back to top

Ambient conditions

Ambient temperature (operation) -40 °C ... 125 °C
Back to top

Mechanical characteristics

Conductor cross section 0.14 mm² ... 1.5 mm² (flexible)
Connection cross section AWG 22 ... 16
Stripping length of the individual wire 8 mm
Contact diameter 1.6 mm
Conductor cross section flexible max. 1.5 mm²
Insertion/withdrawal cycles >= 500
Back to top

General

Note Connectors may only be connected/disconnected when under no load.
Please note that full assembly with the maximum conductor cross-section can cause the sheathed cable to have an impermissibly large external diameter. Dimension the conductor cross-section depending on the number of positions.
The contact carriers are not suitable for installation in VC-MP-K… coupling housings
Size VC2
Series VC-D
Connection technology Crimp connection
Contact type turned
Flammability rating according to UL 94 V0
Degree of pollution 2
Contact carrier type Fixed number of positions
Back to top

Material data

Contact material CuZn
Contact surface material Nickel-plated
Contact carrier material PA-GF
Back to top

Standards and Regulations

Connection in acc. with standard CUL
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Back to top

Environmental Product Compliance

China RoHS Environmentally Friendly Use Period = 50 years
For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration”
Back to top

Classifications

ECLASS

ECLASS 10.0.1 27440205
ECLASS 11.0 27440223
ECLASS 4.0 27140800
ECLASS 4.1 27140800
ECLASS 5.0 27143400
ECLASS 5.1 27261200
ECLASS 6.0 27261200
ECLASS 7.0 27440205
ECLASS 9.0 27440205
Back to top

ETIM

ETIM 2.0 EC000438
ETIM 3.0 EC000438
ETIM 4.0 EC000438
ETIM 6.0 EC000438
Back to top

UNSPSC

UNSPSC 6.01 30211923
UNSPSC 7.0901 39121522
UNSPSC 11 39121522
UNSPSC 12.01 39121522
UNSPSC 13.2 39121522
UNSPSC 18.0 39121522
UNSPSC 19.0 39121522
UNSPSC 20.0 39121522
UNSPSC 21.0 39121522
Back to top

PHOENIX CONTACT

586 Fulling Mill Road
Middletown, PA 17057
(800) 888-7388

  • Create PDF
  • Send by Email
  • Feedback