Products A-Z

Repeater power supply - MINI MCR-2-RPSS-I-2I - 2905628

4-way power supply doubler with plug-in connection technology. HART-transparent, 0(4) mA ... 20 mA input signal, 0(4) mA ... 20 mA output signals. The device can be used in both signal and power supply doubler modes. Screw connection technology.

Price:

Overview

Technical data

Accessories

Approvals

Downloads

Drawings

Block diagram  

Block diagram
Pictogram  

Pictogram
Back to top

Note

Utilization restriction EMC: class A product, see manufacturer's declaration in the download area
Back to top

Dimensions

Width 6.2 mm
Height 109.81 mm
Depth 119.2 mm
Back to top

Ambient conditions

Ambient temperature (operation) -40 °C ... 70 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Maximum altitude ≤ 2000 m
Permissible humidity (operation) 5 % ... 95 % (non-condensing)
Degree of protection IP20 (not assessed by UL)
Noise immunity EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
Back to top

Input data

Description of the input Current input (sensor circuit)
Number of inputs 1
Current input signal 4 mA ... 20 mA (Power supply and signal duplicator mode)
0 mA ... 20 mA (Signal duplicator mode)
Input resistance current input 90 Ω (+1.6 V)
Transmitter supply voltage > 19.5 V
Back to top

Output data

Output name Current output
Number of outputs 2
Current output signal 4 mA ... 20 mA (Power supply and signal duplicator mode)
0 mA ... 20 mA (Signal duplicator mode)
Max. output current 25 mA
Load/output load current output ≤ 500 Ω (per channel)
Ripple < 20 mVPP (at 500 Ω)
Transmission Behavior 1:1 to input signal
Back to top

Power supply

Nominal supply voltage 24 V DC
Supply voltage range 9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
Typical current consumption 40 mA (For 24 V DC and in signal duplicator mode)
65 mA (For 24 V DC and in power supply duplicator mode)
75 mA (For 12 V DC and in signal duplicator mode)
130 mA (For 12 V DC and in power supply duplicator mode)
Power consumption 1.6 W (at IOUT = 20 mA, 500 Ω load)
Back to top

Connection data

Connection method Screw connection
Stripping length 10 mm
Screw thread M3
Conductor cross section solid 0.2 mm² ... 1.5 mm² (with ferrule)
0.14 mm² ... 2.5 mm² (without ferrule)
Conductor cross section flexible 0.14 mm² ... 2.5 mm²
Conductor cross section AWG 24 ... 12 (flexible)
Torque 0.5 Nm ... 0.6 Nm
Back to top

General

No. of channels 2
Maximum transmission error 0.05 % (of final value)
Maximum temperature coefficient 0.0075 %/K
Limit frequency (3 dB) > 1 kHz (typ.)
Step response (10-90%) < 400 µs (typ.)
Electrical isolation Reinforced insulation in accordance with IEC 61010-1
Overvoltage category II
Degree of pollution 2
Rated insulation voltage 300 V
Test voltage, input/output/supply 3 kV (50 Hz, 1 min.)
Electromagnetic compatibility Conformance with EMC directive
Noise emission EN 61000-6-4
Noise immunity EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
Color gray
Housing material PBT
Mounting position any
Assembly instructions The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.
Fire protection for rail vehicles (DIN EN 45545-2) R22 HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R23 HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R24 HL 1 - HL 2
Back to top

Data communication (bypass)

Limit frequency (3 dB) approx. 1 kHz
Back to top

EMC data

Designation Electromagnetic RF field
Standards/regulations EN 61000-4-3
Designation Fast transients (burst)
Standards/regulations EN 61000-4-4
Designation Conducted interferences
Standards/regulations EN 61000-4-6
Back to top

Standards and Regulations

Electromagnetic compatibility Conformance with EMC directive
Noise emission EN 61000-6-4
Standards/regulations EN 61000-4-2
Designation Electromagnetic RF field
Standards/regulations EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
Designation Conducted interferences
Standards/regulations EN 61000-4-6
Electrical isolation Reinforced insulation in accordance with IEC 61010-1
Back to top

Conformance/approvals

Designation CE
Identification CE-compliant
Designation ATEX
Identification  II 3 G Ex ec ic IIC T4 Gc
Certificate BVS 19 ATEX E 047 X
Designation IECEx
Identification Ex ec ic IIC T4 Gc
Certificate IECEx BVS 19.0041X
Designation UL, USA/Canada
Identification UL 508 Listed
Class I, Div. 2, Groups A, B, C, D T5
Class I, Zone 2, Group IIC T5
Designation Shipbuilding approval
Certificate DNV GL TAA000021E
Temperature B
Humidity B
Vibration A
EMC A
Enclosure Required protection according to the Rules shall be provided upon installation on board
Back to top

Environmental Product Compliance

REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration”
Back to top

Classifications

eCl@ss

eCl@ss 10.0.1 27210120
eCl@ss 11.0 27210120
eCl@ss 4.0 27210100
eCl@ss 4.1 27210100
eCl@ss 5.0 27210100
eCl@ss 5.1 27210100
eCl@ss 6.0 27210100
eCl@ss 7.0 27210120
eCl@ss 8.0 27210120
eCl@ss 9.0 27210120
Back to top

ETIM

ETIM 4.0 EC002653
ETIM 5.0 EC002653
ETIM 6.0 EC002653
ETIM 7.0 EC002653
Back to top

PHOENIX CONTACT

586 Fulling Mill Road
Middletown, PA 17057
(800) 888-7388
  • Create PDF
  • Send by Email
  • Feedback