Protective cap - PV-C PROTECTION CAP - 1785430

Photovoltaic connector, Range of articles: SUNCLIX, Protective cap, color: black. self-sealing, without interlock, set consisting of: 1 protective cap for connector side and 1 protective cap for coupling side



Technical data



Ambient conditions

Ambient temperature (operation) -40 °C ... 85 °C
Back to top


Degree of protection IP65/IP68 (2m/24h)
Nominal cross section 0 mm²
Back to top


Color black
Insulating material TPE
Back to top

Standards and Regulations

Safety note • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at under the product
• The installation notes/Design In documents online on the download page at must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
Back to top

Environmental Product Compliance

China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values
Back to top



eCl@ss 10.0.1 27440208
eCl@ss 11.0 27440208
eCl@ss 4.0 27260700
eCl@ss 4.1 27260700
eCl@ss 5.0 27260700
eCl@ss 5.1 27260700
eCl@ss 6.0 27261200
eCl@ss 7.0 27440208
eCl@ss 8.0 27440208
eCl@ss 9.0 27440208
Back to top


ETIM 3.0 EC001121
ETIM 4.0 EC001121
ETIM 5.0 EC002314
ETIM 6.0 EC002314
ETIM 7.0 EC002314
Back to top


UNSPSC 6.01 30211810
UNSPSC 7.0901 39121409
UNSPSC 11 39121409
UNSPSC 12.01 39121409
UNSPSC 13.2 39121421
UNSPSC 18.0 39121421
UNSPSC 19.0 39121421
UNSPSC 20.0 39121421
UNSPSC 21.0 39121421
Back to top

SEA Pte. Ltd.

105 Eunos Avenue 3
Singapore 409836
+65 6228 4900
  • Create PDF
  • Recommend
  • Feedback