Bus system connector - SACC-M12MSB-5CON-PG9 SH AU - 1507764

Bus system connector, PROFIBUS, INTERBUS, 5-position, shielded, Plug straight M12, B-coded, Screw connection, knurl material: Zinc die-cast, nickel-plated, cable gland Pg9, external cable diameter 6.5 mm ... 8.5 mm



Technical data





Functional drawing  

Functional drawing

Dimensional drawing  

Dimensional drawing
Plug, M12 x 1, straight, shielded

Schematic diagram  

Schematic diagram
Cable connection side M12 (screw connection)

Schematic diagram  

Schematic diagram
Pin assignment M12 male connector, 5-pos., B-coded, male side

Back to top


Diameter housing 20 mm
Length 62 mm
External cable diameter 6.5 mm ... 8.5 mm
Stripping length of the sheath 33 mm (for outside cable diameter < 5.5 mm, strip 21 mm off and fold the cable shield back over the cable sheath)
Stripping length of the individual wire 5 mm
Back to top

Ambient conditions

Ambient temperature (operation) -40 °C ... 85 °C (Plug / socket)
Degree of protection IP67
Back to top


Note NOTE: Observe the permissible bending radii when laying conductors, since the degree of protection may be put in jeopardy if the bending forces are too high. Alleviate mechanical loads upstream of the connector, e.g. by using cable ties.
Rated current at 40°C 4 A
Rated voltage 48 V AC
60 V DC
Number of positions 5
Insulation resistance ≥ 100 MΩ
Coding B - inverse
Standards/regulations M12 connector IEC 61076-2-101
Signal type/category PROFIBUS
Status display No
Overvoltage category II
Degree of pollution 3
Connection method Screw connection
Conductor cross section 0.25 mm² ... 0.75 mm² (without ferrule)
0.14 mm² ... 0.75 mm² (with ferrule)
0.25 mm² ... 0.75 mm² (solid)
Conductor cross section AWG 24 ... 18 (without ferrule)
26 ... 20 (with ferrule)
Insertion/withdrawal cycles ≥ 100
Torque 0.4 Nm (M12 knurl)
0.2 Nm (Screw terminal blocks)
0.8 Nm ... 1 Nm (Pressure nut with 4 mm ... 8 mm external cable diameter)
1 Nm ... 1.4 Nm (Pressure nut with 8 mm ... 12 mm external cable diameter)
Tightening torque Screw plug insert with sleeve housing as far it will go
Assembly instructions The wires can be connected both with ferrules and without ferrules
Back to top


Flammability rating according to UL 94 HB
Contact material CuZn
Contact surface material Au
Contact carrier material PA 6.6
Material of grip body Zinc die-cast, nickel-plated
Material, knurls Zinc die-cast, nickel-plated
Sealing material NBR
Back to top

Standards and Regulations

Standard designation M12 connector
Standards/regulations IEC 61076-2-101
Connection in acc. with standard CUL
Flammability rating according to UL 94 HB
Back to top

Environmental Product Compliance

REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50
For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration”
Back to top



eCl@ss 4.0 27140815
eCl@ss 4.1 27140815
eCl@ss 5.0 27260701
eCl@ss 5.1 27260700
eCl@ss 6.0 27279200
eCl@ss 7.0 27440104
eCl@ss 8.0 27440104
eCl@ss 9.0 27440102
Back to top


ETIM 2.0 EC001121
ETIM 3.0 EC002062
ETIM 4.0 EC002062
ETIM 5.0 EC002062
ETIM 6.0 EC002062
Back to top


UNSPSC 6.01 31251501
UNSPSC 7.0901 31251501
UNSPSC 11 31251501
UNSPSC 12.01 31251501
UNSPSC 13.2 39121413
Back to top


C6 The Exchange
Calmount Park
Dublin 12
D12 XE18
  • Create PDF
  • Recommend
  • Feedback

This website uses cookies, by continuing to browse, you agree to our cookie policy. Read our privacy policy for more information.