CHARX T1HBI12-DC250-2,0M1 - Vehicle charging inlet

1211606

CHARX connect universal, DC CCS Typ 1, Vehicle charging inlet, 250 A permanent, 1000 V DC, Single wires, length: 2 m, locking actuator: 12 V, 4-pos., Front and rear mounting, M6, housing: black, for charging with direct current (DC), IEC 62196-2, IEC 62196-3, A protective cap is supplied as standard for the DC contacts.

Tuotetiedot

Tuotekuvaus

General	A protective cap is supplied as standard for the DC contacts.

Product type	Vehicle charging inlet
Product family	CHARX connect universal
Technology	Combined Charging System
Application	for charging with direct current (DC)
	for installation in electric vehicles (EV)
Charging standard	DC CCS Typ 1
Charging mode	Mode 4
Customer variations	On request

Note on the connection method	Crimp connection, cannot be disconnected
Temperature measurement	DC contacts: 2x PT1000 (DIN EN 60751)
Charging power and current (DC charging)
Type of charging current	DC
Charging current	250 A DC
Charging power	250 kW
Pin assignment (Leistungskontakte)
Number	5 (L1, N, PE, DC+, DC-)
Rated voltage	1000 V DC
Rated current	250 A DC
Pin assignment (Signalkontakte)
Type of signal transmission	Pulse width modulation with modulated Powerline communication in accordance with ISO/IEC 15118 / DIN SPEC 70121
Number	2 (CP, CS)
Rated voltage	30 V AC
Rated current	2 A
Coding	2.7 kΩ (between PE and CS)
Insulation resistance	> 200 MΩ
Locking actuator
Locking actuator	12 V, 4-pos.
	Top center position
Possible power supply range at the motor	9 V ... 16 V
Maximum voltage for locking detection	12 V
Typical motor current for locking	0.25 A
Reverse current of the motor	max. 1.5 A
Max. dwell time with reverse current	1 s
Recommended adaptation time	600 ms
Pause time after entry or exit path	3 s
Service life insertion cycles	> 10000 load cycles
Lock recognition	available
Mechanical emergency release	available
Ambient temperature (operation)	-40 °C ... 80 °C
Temperature sensors (Pt 1000)
Sensor type	Pt 1000
Standards/regulations	DIN EN 60751
Attachment point	2 sensors for the DC contacts

Vehicle charging inlet
Width	108 mm
Height	151.2 mm
Depth	122.8 mm
Bore dimensions
Width	117.6 mm
Height	90 mm
Depth	117.6 mm

Color (Housing)	black (9005)
Color (Mating face)	black (9005)
Material (Housing)	Plastic
Material (Contact surface)	Silver

Cable length	2 m
Cable type	Single wires
Single-core wires for DC
Cable length	2 m
Cable structure	2 x 95 mm²
Single wire, material	Silicone
Single wire, color	OG
External cable diameter	20.60 mm ±0.3 mm
Cable resistance	≤ 0.196 Ω/km
Single-core wire for PE
Cable length	2 m
Cable structure	1 x 25 mm²
Single wire, material	Silicone
Single wire, color	GN/YE
External cable diameter	8.60 mm ±0.1 mm
Cable resistance	≤ 0.743 Ω/km
Single-core wires for locking actuator
Cable length	1.5 m
Cable structure	4 x 0.5 mm²
Single wire, material	PVC
Single wire, color	BU/RD, BU/GN, BU/YE, BU/BN
External cable diameter	1.60 mm ±0.20 mm
Cable resistance	≤ 37.1 Ω/m
Single-core wires for Pt 1000 temperature sensors
Cable length	0.9 m
Cable structure	3 x 0.5 mm²
Single wire, material	PVC
Single wire, color	BN
	GN
	YE
External cable diameter	1.60 mm ±0.20 mm
Cable resistance	≤ 37.1 Ω/m
Single-core wires for communication
Cable length	1 m
Cable structure	2 x 0.5 mm²
Single wire, material	PVC
Single wire, color	BK
	WH
External cable diameter	1.60 mm ±0.20 mm
Cable resistance	≤ 37.1 Ω/m

Mechanical data
Insertion/withdrawal cycles	> 10000
Insertion force	< 100 N
Withdrawal force	< 100 N

Ambient conditions
Degree of protection (Vehicle charging inlet)	IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
	IP67 (Inner area of vehicle charging inlet)
Ambient temperature (operation)	-40 °C ... 40 °C (60°C, maximum (current reduction required, observe the DC contact temperature limit value of 90°C))
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	4000 m (above sea level)

Standards
Standards/regulations	IEC 62196-2
	IEC 62196-3
	SAE J1772

Mounting type	Front and rear mounting (0 to 90 degree frontal inclination possible)
Mounting hole diameter	6.70 mm (ø)
Fixing screws	M6
Screws included in the scope of delivery	none

Kaupalliset tiedot

Tuotenumero	1211606
Pakkausyksikkö	1 Kappaletta
Vähimmäistilausmäärä	1 Kappaletta
Tuoteavain	XWCAIB
Tuotekoodi	XWCAIB
GTIN	4063151285043
Paino kappaletta kohti (sis. pakkauksen)	6 579 g
Paino kappaletta kohti (ilman pakkausta)	103 g
Tullitariffinumero	85444290
Alkuperämaa	DE

Luokitukset

Hyväksynnät

Approval Specification Data
	Nimellisjännite U_N	Nimellisvirta I_N	Poikkipinta AWG	Poikkipinta mm²
keine
	1000 V	250 A

Environmental product compliance

Yhteensopivat tuotteet

Lisätarvikkeet

Edut

Complete product range

Uniform, space-saving dimensions for the installation space and the screw connection points of all Phoenix Contact vehicle charging inlets

Developed and produced in accordance with the IATF 16949 automotive standard and ISO 9001

Integrated interlock during charging

Manual emergency release of the locking actuator

Protected and sealed against dirt and water with a high degree of protection

ECLASS-13.0	27144706
ECLASS-15.0	27144706

EU RoHS
Täyttää RoHS-direktiivin vaatimukset	Kyllä
poikkeussäännökset siltä osin kuin ne ovat tiedossa	6(c), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-50 Löydät tuotekohtaisen Kiinan RoHS-ilmoitusluettelon kunkin tuotteen latausalueelta Valmistajan ilmoitus -kohdasta. EFUP-E-merkinnän sisältäville tuotteille ei tarvita Kiinan RoHS-ilmoitusluetteloa, eikä sitä tarvitse siksi laatia.
EU REACH SVHC
Huomautus REACH-kandidaattiaineesta (CAS-nro)	2-ethylhexyl 10-ethyl-4,4-dioctyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate (DOTE) (CAS-nro: 15571-58-1)
		Lead (CAS-nro: 7439-92-1)
		Bis(2-(2-methoxyethoxy)ethyl)ether (CAS-nro: 143-24-8)
		6,6'-di-tert-butyl-2,2'-methylenedi-p-cresol (CAS-nro: 119-47-1)
SCIP	52b1c744-ce32-4a5d-9fe2-cc6941a65f57

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

CHARX T1HBI12-DC250-2,0M1 - Vehicle charging inlet

1211606

Tuotetiedot

ECLASS

ETIM

UNSPSC

cULus Recognized

Yhteensopivat tuotteet

Edut

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

CHARX T1HBI12-DC250-2,0M1 - Vehicle charging inlet 1211606

Tuotetiedot

ECLASS

ETIM

UNSPSC

Yhteensopivat tuotteet

CHARX T1HBI-DUST-COVER-SET - Protective cover 1305482

CHARX T1HI-ELOCK12V - Locking 1331528

Edut

CHARX T1HBI12-DC250-2,0M1 - Vehicle charging inlet

1211606