Extension module - PSR-SPP- 24UC/URM4/5X1/2X2/B
2981046

Single or two-channel contact extension, 5 N/O contacts, 1 N/C contact, 1 confirmation current path, width: 22.5 mm, pluggable Push-in terminal block

Maksuton lataus saatavilla. Ladattavat tiedostot

Tuotetiedot




Product type Safety relays
Application Extension module
Mechanical service life 10x 106 cycles
Relay type Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3
Insulation characteristics
Overvoltage category III

Maximum power dissipation for nominal condition 2.21 W
Nominal operating mode 100% operating factor
Rated insulation voltage 250 V AC
Rated surge voltage/insulation Basic insulation 4 kV:
between all current paths and housing
Safe isolation, reinforced insulation 6 kV:
between A1/A2, 11/12, 23/24, 71/72 and 33/34, 43/44, 53/54, 63/64

General
Rated control circuit supply voltage US 24 V AC/DC -15 % / +10 %
Power consumption at US typ. 1.94 W (AC)
typ. 1.7 W (DC)
Rated control supply current IS typ. 81 mA AC
typ. 71 mA DC
Inrush current 175 mA (Δt = 5 ms at Us)
Filter time 2 ms (at A1 in the event of voltage dips at Us)
Typ. starting time with Us < 20 ms (when controlled via A1)
Typical release time < 20 ms (when controlled via A1)
Recovery time < 1 s
Maximum switching frequency 1 Hz
Protective circuit Surge protection; Varistor
Operating voltage display 1 x green LED

Contact type 5 enabling current paths
1 signaling current path
1 confirmation current path
Contact material AgSnO2
Maximum switching voltage 250 V AC/DC (Observe the load curve)
Minimum switching voltage 5 V AC/DC
Limiting continuous current 6 A (N/O contact, pay attention to the derating)
6 A (N/C contact)
Maximum inrush current 20 A (Δt  100 ms)
Inrush current, minimum 10 mA
Sq. Total current 72 A2 (observe derating)
Interrupting rating (ohmic load) max. 144 W (24 V DC, τ = 0 ms)
288 W (48 V DC, τ = 0 ms)
110 W (110 V DC, τ = 0 ms)
88 W (220 V DC, τ = 0 ms)
1500 VA (250 V AC, τ = 0 ms)
Maximum interrupting rating (inductive load) 42 W (24 V DC, τ = 40 ms)
42 W (48 V DC, τ = 40 ms)
42 W (110 V DC, τ = 40 ms)
42 W (220 V DC, τ = 40 ms)
Switching capacity min. 50 mW
Switching capacity (360/h cycles) 4 A (24 V DC)
4 A (230 V AC)
Switching capacity (3600/h cycles) 2.5 A (24 V (DC13))
3 A (230 V (AC15))
Output fuse 10 A gL/gG (N/O contact)
6 A gL/gG (N/C contact)

Connection technology
pluggable yes
Conductor connection
Connection method Push-in connection
Conductor cross section solid 0.2 mm² ... 1.5 mm²
Conductor cross section flexible, with ferrule without plastic sleeve 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross-section AWG 24 ... 16

Width 22.5 mm
Height 112 mm
Depth 114.5 mm

Housing material Polyamide
Housing color yellow

Safety data
Stop category 0
Safety data: EN ISO 13849
Category 4 (In conjunction with suitable evaluating device)
Performance level (PL) e (In conjunction with suitable evaluating device)
Safety data: IEC 61508 - High demand
Equipment type Type A
Safety Integrity Level (SIL) 3 (In conjunction with suitable evaluating device)
Probability of a hazardous failure per hour (PFHD) 1.02 x 10-10
Proof test interval 240 Months
Duration of use 240 Months
Safety data: IEC 61508 - Low demand
Equipment type Type A
Safety Integrity Level (SIL) 3 (In conjunction with suitable evaluating device)
Probability of a hazardous failure on demand (PFDAVG) 1.50 x 10-4
Proof test interval 84 Months
Duration of use 240 Months

Ambient conditions
Degree of protection IP20
Min. degree of protection of inst. location IP54
Ambient temperature (operation) -20 °C ... 55 °C (observe derating)
Ambient temperature (storage/transport) -40 °C ... 70 °C
Maximum altitude max. 2000 m (Above sea level)
Max. permissible humidity (storage/transport) 75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation) 75 % (on average, 85% infrequently, non-condensing)
Shock 15g
Vibration (operation) 10 Hz ... 150 Hz, 2g

CE
Certificate CE-compliant

Air clearances and creepage distances between the power circuits
Standards/regulations DIN EN 50178/VDE 0160

Mounting type DIN rail mounting
Assembly instructions See derating curve
Mounting position vertical or horizontal

Tuotenumero 2981046
Pakkausyksikkö 1 Kappaletta
Vähimmäistilausmäärä 1 Kappaletta
Tuoteavain DNA152
Tuotekoodi DNA152
Luettelosivu Sivu 232 (C-6-2019)
GTIN 4017918915520
Paino kappaletta kohti (sis. pakkauksen) 207,4 g
Paino kappaletta kohti (ilman pakkausta) 20,4 g
Tullitariffinumero 85371098
Alkuperämaa DE


ECLASS

ECLASS-9.0 27371819
ECLASS-10.0.1 27371819
ECLASS-11.0 27371819

ETIM

ETIM 8.0 EC001449

UNSPSC

UNSPSC 21.0 39122200

EAC

Hyväksyntätunnus: TR TS_D_01838-19

UL Listed

Hyväksyntätunnus: FILE E 140324

cUL Listed

Hyväksyntätunnus: FILE E 140324

Functional Safety

Hyväksyntätunnus: 968/FSP 1265.02/21

Functional Safety

Hyväksyntätunnus: 968/FSP 1265.02/21

cULus Listed


REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Edut

1- and 2-channel control
Up to Cat. 4/PL e in accordance with EN ISO 13849-1, SIL 3 in accordance with IEC 62061, SIL 3 in accordance with IEC 61508