External part, with current bar
CSA
| Nominal voltage UN | 300 V |
|---|---|
| Nominal current IN | 65 A |
| AWG/kcmil | 22-6 |
| Min. cross section | 22 mm² |
| Max. cross section | 6 mm² |
Panel feed-through terminal block, connection method: Screw connection with tension sleeve, Screw connection with tension sleeve, number of positions: 1, load current: 57 A, cross section: 0.5 mm2 - 16 mm2, connection direction of the conductor to plug-in direction: 0 °, width: 10.1 mm, color: green-yellow
External part, with current bar
| Electrical properties | |
| Rated surge voltage (III/2) | 6 kV |
| Pollution degree | 3 |
| Rated voltage (III/3) | 400 V |
| Air clearances and creepage distances | 4․ Insulation coordination | |
| minimum clearance value - non-homogenous field (II/2) | 8 mm |
| minimum creepage distance (III/3) | 10 mm |
| minimum clearance value - non-homogenous field (III/3) | 8 mm |
| Insulating material group | I |
| minimum clearance value - non-homogenous field (III/2) | 8 mm |
| minimum creepage distance (III/2) | 8 mm |
| Comparative tracking index (IEC 60112:2003-01) | CTI 600 |
| minimum creepage distance (II/2) | 8 mm |
| Rated surge voltage (II/2) | 8 kV |
| Rated insulation voltage (III/3) | 800 V |
| Rated insulation voltage (III/2) | 1000 V |
| Specification | IEC 60947-1:2007-06 + A1:2010-12 |
| Rated insulation voltage (II/2) | 1000 V |
| Rated surge voltage (III/3) | 8 kV |
| Rated surge voltage (III/2) | 8 kV |
| Application | Plastic panel with DP-HDFK 10-5,5 |
| Air clearances and creepage distances | 3․ Insulation coordination | |
| minimum clearance value - non-homogenous field (II/2) | 5.5 mm |
| minimum creepage distance (III/3) | 6.3 mm |
| minimum clearance value - non-homogenous field (III/3) | 5.5 mm |
| Insulating material group | I |
| minimum clearance value - non-homogenous field (III/2) | 5.5 mm |
| minimum creepage distance (III/2) | 5.5 mm |
| Comparative tracking index (IEC 60112:2003-01) | CTI 600 |
| minimum creepage distance (II/2) | 5.5 mm |
| Rated surge voltage (II/2) | 6 kV |
| Rated insulation voltage (III/3) | 500 V |
| Rated insulation voltage (III/2) | 500 V |
| Specification | IEC 60947-1:2007-06 + A1:2010-12 |
| Rated insulation voltage (II/2) | 1000 V |
| Rated surge voltage (III/3) | 6 kV |
| Rated surge voltage (III/2) | 6 kV |
| Application | Plastic panel |
| Air clearances and creepage distances | 2․ Insulation coordination | |
| minimum clearance value - non-homogenous field (II/2) | 3 mm |
| minimum creepage distance (III/3) | 3.2 mm |
| minimum clearance value - non-homogenous field (III/3) | 3 mm |
| Insulating material group | I |
| minimum clearance value - non-homogenous field (III/2) | 3 mm |
| minimum creepage distance (III/2) | 3 mm |
| Comparative tracking index (IEC 60112:2003-01) | CTI 600 |
| minimum creepage distance (II/2) | 3 mm |
| Rated surge voltage (II/2) | 4 kV |
| Rated insulation voltage (III/3) | 250 V |
| Rated insulation voltage (III/2) | 250 V |
| Specification | IEC 60947-1:2007-06 + A1:2010-12 |
| Rated insulation voltage (II/2) | 500 V |
| Rated surge voltage (III/3) | 4 kV |
| Rated surge voltage (III/2) | 4 kV |
| Application | Metal wall > 2.5 mm ... 4.0 mm |
| Air clearances and creepage distances | 1․ Insulation coordination | |
| minimum clearance value - non-homogenous field (II/2) | 5.5 mm |
| minimum creepage distance (III/3) | 5.5 mm |
| minimum clearance value - non-homogenous field (III/3) | 5.5 mm |
| Insulating material group | I |
| minimum clearance value - non-homogenous field (III/2) | 5.5 mm |
| minimum creepage distance (III/2) | 5.5 mm |
| Comparative tracking index (IEC 60112:2003-01) | CTI 600 |
| minimum creepage distance (II/2) | 5.5 mm |
| Rated surge voltage (II/2) | 6 kV |
| Rated insulation voltage (III/3) | 400 V |
| Rated insulation voltage (III/2) | 500 V |
| Specification | IEC 60947-1:2007-06 + A1:2010-12 |
| Rated insulation voltage (II/2) | 1000 V |
| Rated surge voltage (III/3) | 6 kV |
| Rated surge voltage (III/2) | 6 kV |
| Application | Metal wall 1.0 mm ... 2.5 mm |
| Nominal current IN | 57 A |
| 57 A |
| Type of packaging | packed in cardboard |
| Dimensional drawing |
|
| Pitch | 10.1 mm |
| Width | 10.1 mm |
| External dimensions | |
| Length_external | 18.1 mm |
| Height_external | 28.5 mm |
| Internal dimensions | |
| Height_inside | 31 mm |
| Length_inside | 24.5 mm |
| Note on application | The technical data applies when using internal part HDFK 10I - 0707840 |
| Safety note | |
| Safety note | • Only electrically qualified personnel may install and operate the product. To recognize and prevent danger, the qualified personnel must be familiar with the basics of electrical engineering. |
| • Observe the technical data provided here and refer to the documents listed under “Downloads”. The download area contains important information, such as installation notes, technical drawings, and 3D data. | |
| • The cable entry funnel is not safe to touch. Never connect or disconnect the terminal when it is energized. Take appropriate steps to ensure touch protection. | |
| There is no electrical contact to the housing. Make sure that protective grounding is provided for green/yellow color variants and articles marked with PE. | |
| Connection technology | |
| Nominal cross section | 10 mm2 |
| Conductor connection exterior | |
| 2 conductors with same cross section, solid | 0.5 mm2 ... 4 mm2 |
| Torque | 1.5 Nm ... 1.8 Nm |
| Conductor cross section flexible, with ferrule without plastic sleeve | 0.5 mm2 ... 10 mm2 |
| Internal cylindrical gage | B6 |
| 2 conductors with same cross section, flexible, with ferrule without plastic sleeve | 0.5 mm2 ... 2.5 mm2 |
| Conductor cross section solid | 0.5 mm2 ... 16 mm2 |
| Stripping length | 10 mm |
| 2 conductors with the same cross section, flexible, with TWIN ferrule with plastic sleeve | 0.5 mm2 ... 6 mm2 |
| Connection method | Screw connection with tension sleeve |
| 2 conductors with same cross section, flexible | 0.5 mm2 ... 4 mm2 |
| Conductor cross section, flexible, with ferrule, with plastic sleeve | 0.5 mm2 ... 10 mm2 |
| Conductor cross section flexible | 0.5 mm2 ... 10 mm2 |
| Connection direction of the conductor to plug-in direction | 0 ° |
| Conductor connection interior | |
| 2 conductors with same cross section, solid | 0.5 mm2 ... 4 mm2 |
| Torque | 1.5 Nm ... 1.8 Nm |
| Conductor cross section flexible, with ferrule without plastic sleeve | 0.5 mm2 ... 10 mm2 |
| Internal cylindrical gage | B6 |
| 2 conductors with same cross section, flexible, with ferrule without plastic sleeve | 0.5 mm2 ... 2.5 mm2 |
| Conductor cross section solid | 0.5 mm2 ... 16 mm2 |
| Stripping length | 10 mm |
| 2 conductors with the same cross section, flexible, with TWIN ferrule with plastic sleeve | 0.5 mm2 ... 6 mm2 |
| Connection method | Screw connection with tension sleeve |
| 2 conductors with same cross section, flexible | 0.5 mm2 ... 4 mm2 |
| Conductor cross section, flexible, with ferrule, with plastic sleeve | 0.5 mm2 ... 10 mm2 |
| Conductor cross section flexible | 0.5 mm2 ... 10 mm2 |
| Connection direction of the conductor to plug-in direction | 0 ° |
| Material data - housing | |
| Insulating material group | I |
| Temperature for the ball pressure test according to EN 60695-10-2 | 125 °C |
| Glow wire flammability index GWFI according to EN 60695-2-12 | 850 |
| CTI according to IEC 60112 | 600 |
| Housing color | green-yellow (6021 / 1018) |
| Insulating material | PA |
| Flammability rating according to UL 94 | V0 |
| Glow wire ignition temperature GWIT according to EN 60695-2-13 | 775 |
| Material data - contact | |
| Contact material | Cu alloy |
| Surface characteristics | tin-plated |
| Note | WEEE/RoHS-compliant, free of whiskers according to IEC 60068-2-82/JEDEC JESD 201 |
| Number of positions | 1 |
| Nominal voltage UN | 300 V |
|---|---|
| Nominal current IN | 65 A |
| AWG/kcmil | 22-6 |
| Min. cross section | 22 mm² |
| Max. cross section | 6 mm² |
| Usegroup | B | C | D |
|---|---|---|---|
| Nominal voltage UN | 300 V | 150 V | 300 V |
| Nominal current IN | 65 A | 65 A | 10 A |
| AWG/kcmil | 22-6 | 22-6 | 22-6 |
| Min. cross section | 24 mm² | 24 mm² | 24 mm² |
| Max. cross section | 6 mm² | 6 mm² | 6 mm² |