H distributor - PRC ED-H 1I5/3O5-4-HR-GN

Power distributor, Range of articles: PRC 35, H distributor, type: H-distributor, housing material: Polycarbonate fiber reinforced, color: black, rated voltage: 400 V, rated current: 32 A, Connection method: pre-assembled, Type of contact: Input: pin / outputs: socket. This item is configurable. For a configuration, please contact your local PHOENIX CONTACT subsidiary.

Product Details

Order information: This item is configurable. For a configuration, please contact your local PHOENIX CONTACT subsidiary.
Safety note
Safety note • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Type H-distributor
Product type Power distributor
Locking type Snap-in locking
Insertion force 70 N ±10 N
Insulation characteristics
Protection class II
Degree of pollution 2

Width 238 mm
Height 129 mm
Length 77 mm

Nominal voltage ATD 400 V
Rated surge voltage (III/2) 8 kV
Rated current 32 A (observe derating)

Mechanical data
Insertion force 70 N ±10 N

Color black
Color of the housing part black
Flammability rating according to UL 94 V0
Seal material TPE
Contact material Copper alloy
Contact surface material Silver
Contact carrier material PPE
O-ring material Silicon
Material of locking screw Polycarbonate, fiber-reinforced
Cable gland material PPE
Housing material Polycarbonate fiber reinforced

Insertion/withdrawal cycles 2000

Ambient conditions
Halogen-free yes

Degree of protection IP66/67/69
Ambient temperature (operation) -40 °C ... 70 °C (Depending on the current carrying capacity/derating curve)
Ambient temperature (storage/transport) -40 °C ... 70 °C
Ambient temperature (assembly) -5 °C ... 85 °C

Item number 1079660
Packing unit 1 pc
Minimum order quantity 1 pc
Sales Key A16
Product Key ABLCCA
GTIN 4055626801100
Weight per Piece (including packing) 703.4 g
Weight per Piece (excluding packing) 703.4 g
Customs tariff number 85444290
Country of origin PL


ECLASS-9.0 27440103
ECLASS-10.0.1 27440109
ECLASS-11.0 27440109


ETIM 8.0 EC003569


UNSPSC 21.0 39121400

REACh SVHC Lead 7439-92-1

Your advantages

Time-saving Plug and Play installation with pre-assembled distributor boxes
Locking mechanism can be unlocked manually or using a tool
Ideal for indoor and outdoor use due to weatherproof materials
Customer-specific versions and assembly available on request