Contact insert - VC-D1-BU15-PE-R
1884801

Contact insert, Range of articles: VARIOCON, Contact insert, type: VC1, housing material: PA, number of positions: 15, min. conductor cross section: 0.14 mm2, max. conductor cross section: 1.5 mm2, rated voltage: 250, rated current: 10 A, Connection method: Crimp connection, Type of contact: Socket. Connectors may only be connected/disconnected when under no load.


Product Details




General Connectors may only be connected/disconnected when under no load.
General Please note that full assembly with the maximum conductor cross-section can cause the sheathed cable to have an impermissibly large external diameter. Dimension the conductor cross-section depending on the number of positions.
General The contact carriers are not suitable for installation in VC-MP-K… coupling housings
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Type VC1
Product type Contact insert
Number of positions 15
Connection profile 15+PE
Contact type rolled
Series VC-D
Insulation characteristics
Degree of pollution 2

Rated voltage (II/2) 250 V
Rated voltage (III/3) 250 V
Rated voltage (III/3) 250 V
Nominal voltage ATD 250 (III/2)
Rated surge voltage 4 kV
Rated surge voltage (II/2) 2.5 kV
Rated surge voltage (III/2) 4 kV
Rated surge voltage 4 kV
Rated current 10 A
Rated current 10 A
Rated current max. 10 A
Nominal voltage UN 250 V

Dimensional drawing
Width 25.4 mm
Height 33 mm
Length 48.6 mm
Mechanical characteristics
Contact diameter 1.6 mm

Color of the housing part black
Material Polyamide
Flammability rating according to UL 94 V0
Insulating material group IIIa
Contact material CuZn
Contact surface material Ni
Contact carrier material PA-GF
Housing material PA

Insertion/withdrawal cycles >= 500

Cable structure
Single wire, cross section 0.14 mm² 1.5 mm²
Stripping length of the individual wire 8 mm

Ambient conditions
Ambient temperature (operation) -40 °C ... 125 °C

Item number 1884801
Packing unit 1 pc
Minimum order quantity 10 pc
Sales Key A16
Product Key ABLACB
Catalog Page Page 39 (C-2-2013)
GTIN 4017918164874
Weight per Piece (including packing) 29.76 g
Weight per Piece (excluding packing) 29.76 g
Customs tariff number 85369010
Country of origin PL


ECLASS

ECLASS-9.0 27440205
ECLASS-10.0.1 27440205
ECLASS-11.0 27440223

ETIM

ETIM 8.0 EC003557

UNSPSC

UNSPSC 21.0 39121400

cUL Recognized

Approval ID: FILE E 118976
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
250 V 4 A

UL Recognized

Approval ID: FILE E 118976
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
250 V 4 A

EAC

Approval ID: B.01687

cULus Recognized


China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values

Your advantages

Positions 15, 30, 50, and 65 are available, in accordance with housing sizes VC 1 - VC 4.
Contact types meet the requirements of IEC 60352/DIN EN 60352
Contact carriers have two further capacitive PE contacts
Pin and socket contacts can be used on both the plug and device sides
The connection data of 250 V/10 A corresponds to that of the HEAVYCON DD series