1. Home
  2. Products
  3. Flush-type connector - SACC-E-M12FSK-4PE-M16XL/0,5
M12 flush-type socket
Pin assignment of M12 socket, 5-pos., K-coded, socket side view
I = current strength, T = ambient temperature

Flush-type connector - SACC-E-M12FSK-4PE-M16XL/0,5
1327576

Flush-type connector, Power, 5-position, Socket, M12, K - Power, Front mounting, M16 x 1.5, Individual wires, cable length: 0.5 m, 2.50 mm2, PEX litz wire

Product Details

Notes on operation The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product type Circular connectors (device side)
Number of positions 5
No. of cable outlets 1
Shielded no
Coding K - Power
Insulation characteristics
Overvoltage category III
Degree of pollution 3
Degree of protection IP67
Degree of protection IP65/IP67
Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket)
-40 °C ... 85 °C (without mechanical actuation)
-25 °C ... 90 °C
-40 °C ... 90 °C (cable, fixed installation)
Insertion/withdrawal cycles > 100
Header 1
Head design Socket
Head thread type M12
Coding K - Power
Rated voltage in acc. with IEC 61076-2-101 630 V
Rated surge voltage 6 kV
Rated surge voltage 6 kV
Contact resistance ≤ 3 mΩ
Insulation resistance ≥ 100 MΩ
Nominal voltage UN 630 V
Nominal current IN 16 A
Test voltage 6 kV
Material PU 2K (Grout material)
Flammability rating according to UL 94 V0
Sealing material FKM
Contact material CuZn
Contact surface material Au
Contact carrier material PA
Cable gland material Zinc die-cast, nickel-plated
Connection technology
Connection method Individual wires
Conductor connection
Connection method Individual wires
Mounting type Front mounting
Assembly instructions Tightening limitation
Flame resistance in acc. with UL FT-2
Other resistance Hydrolysis-resistant
M12
Standards/specifications IEC 61076-2-111
Cable length 0.5 m
Cable structure
Cable type PEX litz wire
Signal type/category Power
Conductor material Tin-plated Cu litz wires
AWG signal line 14
Material wire insulation PE-X
Single wire, color Black 1, black 2, black 3, black 4, green/yellow
Electrical properties
Test voltage Core/Core 6 kV
Ambient conditions
Halogen-free according to IEC 60754-1
Flame resistance in acc. with UL FT-2
Other resistance Hydrolysis-resistant
Ambient temperature (operation) -40 °C ... 85 °C (without mechanical actuation)
Item number 1327576
Packing unit 1 pc
Minimum order quantity 100 pc
Sales Key ABQ
Product Key ABQEAB
GTIN 4063151621414
Weight per Piece (including packing) 101.5 g
Weight per Piece (excluding packing) 22.22 g
Customs tariff number 85444290
Country of origin DE

ECLASS

ECLASS-9.0 27440102
ECLASS-10.0.1 27440102
ECLASS-11.0 27440102

ETIM

ETIM 8.0 EC002635

UNSPSC

UNSPSC 21.0
REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Compatible Products

  1. Flat nut SACC-E-MU-M16 - 1504097

  2. Screw plug PROT M12 MS PWR - 1092802

Your advantages

For compact devices: transmit high power in a confined space
Easy-to-install, optimized XL housing contour with wrench size 19
Mechanical tightening limitation for long-term-stable gasket
Pre-assembled with litz wires for immediate use
Customer-specific assemblies and litz wire lengths available
Sealed on the litz wire side for optimum leak-tightness
For high transmission safety: shield connection to the housing with optional EMC nut