Connector - PV-CM-S 2,5-6 (-)
1774687

Photovoltaic connector, Range of articles: Sunclix, Connector, housing material: PPE, color: black, number of positions: 1, min. conductor cross section: 2.5 mm2, max. conductor cross section: 6 mm2, rated voltage: 1100 V DC, rated current: 40 A, Connection method: Spring-cage, Type of contact: Pin, min. cable diameter: 5.5 mm, max. cable diameter: 8 mm


Product Details




Safety note
Safety note • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.

Product type Photovoltaic connector
Number of positions 1
Pitch 0 mm
Insertion force 45 N ±10 N
Insulation characteristics
Protection class II
Degree of pollution 2

Rated voltage (II/2) 1000 V
Rated voltage (III/2) 1100 V
Rated surge voltage 12.8 kV
Rated surge voltage (II/2) 12 kV
Rated surge voltage (III/2) 12 kV
Rated surge voltage (III/3) 12.8 kV
Rated current (6.0 mm²) 40 A (in accordance with IEC 62852:2014-11)
Rated current (4.0 mm²) 35 A (in accordance with IEC 62852:2014-11)
Rated current (2.5 mm²) 27 A (in accordance with IEC 62852:2014-11)
Contact resistance 0.45 mΩ
Contact resistance ≤ 0.45 mΩ (when plugged in (without cable))

Dimensional drawing
Width 18.6 mm
Height 26.4 mm
Length 58.3 mm
Pitch 0 mm

Color black
Color of the housing part black
Material PPE (Housing)
Flammability rating according to UL 94 V0
Insulating material group III
Insulating material mPPE
Contact surface Tin Sn
Material, insert PPE
Cable seal material EPDM
Contact material Cu
Contact surface material Ag
Contact carrier material PPE
O-ring material EPDM
Housing material PPE

Insertion/withdrawal cycles 100 (Test specification: IEC 60512-9-1:2010-03)

Cable structure
Cable type H1Z2Z2-K lines
External cable diameter 5.5 mm ... 8 mm
5.5 mm ... 8 mm
Single wire, cross section 2.5 mm² 6 mm²
Stripping length of the individual wire 15 mm
Mechanical properties
Cable pull-out force > 330 N

Outside conductor diameter 8 mm 5.5 mm
Mechanical data
Outside conductor diameter 8 mm 5.5 mm
Insertion force 45 N ±10 N
Withdrawal force 250 N ±50 N (when locked)

Ambient conditions
Degree of protection (when plugged in) IP66 / IP68 (2 m / 24 h)
Degree of protection (not plugged in) IP20
Degree of protection IP66 / IP68 (2 m / 24 h)
Ambient temperature (operation) -40 °C ... 85 °C (dependent on the derating curve)
Ambient temperature (assembly) -5 °C ... 50 °C

Item number 1774687
Packing unit 50 pc
Minimum order quantity 50 pc
Sales Key ABL
Product Key ABLBBA
Catalog Page Page 422 (C-2-2013)
GTIN 4046356480192
Weight per Piece (including packing) 13.716 g
Weight per Piece (excluding packing) 13.4 g
Customs tariff number 85359000
Country of origin DE


ECLASS

ECLASS-9.0 27440103
ECLASS-10.0.1 27440109
ECLASS-11.0 27440109

ETIM

ETIM 8.0 EC003569

UNSPSC

UNSPSC 21.0

EAC

Approval ID: B.01687

TÜV Rheinland

Approval ID: R 60126961

China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values

Your advantages

Convenient, secure spring connection technology
High yield, thanks to silver-plated contacts
Convenient release without a special tool
One-piece DC connector