SB-8ESCD8AA700S - Device connector front mounting - 1623719

Product details

Technical data

Notes

Order information:	Crimp contacts, 4 x Ø 0.8 mm, 4 x Ø 1 mm, 5 x Ø 3.6 mm, order separately
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Operate the connector only when it is fully plugged in and interlocked.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties

Product type	Circular connectors (device side)

Connector

Insulating body
Connection method	Crimp connection
Contact switching type	Socket
Application	Hybrid
Number of positions	13
Direction of rotation	Standard
Number Contact (Grp 1 - power contacts or just one contact connection type)	5
Diameter Contact (Grp 1 - power contacts or just one contact connection type)	3.6 mm
Litz wire cross-section min. Contact (Grp 1 - power contacts or just one contact connection type)	1 mm²
Litz wire cross-section max. Contact (Grp 1 - power contacts or just one contact connection type)	10 mm²
Rated current Contact (Grp 1 - power contacts or just one contact connection type)	70 A
Rated voltage Contact (Grp 1 - power contacts or just one contact connection type)	630 V AC
		850 V DC
Rated surge voltage	6 kV
Overvoltage category	III
Degree of pollution	3
Number Contact	4
Diameter Contact	1 mm
Litz wire cross-section min. Contact	0.06 mm²
Litz wire cross-section max. Contact	1.5 mm²
Rated voltage Contact	500 V
Rated surge voltage	1.5 kV
Overvoltage category	III
Degree of pollution	3
Number Contact (Contact group 3)	4
Diameter Contact (Contact group 3)	0.8 mm
Litz wire cross-section min. Contact (Contact group 3)	0.08 mm²
Litz wire cross-section max. Contact (Contact group 3)	0.5 mm²
Rated voltage Contact (Contact group 3)	50 V
Rated surge voltage	1.5 kV
Overvoltage category	III
Degree of pollution	3
Installation height	2000 m (4000 m at 300 V system voltage in accordance with DIN EN 606664-1)
Housing
Thread type	M40
Type of locking	for standard and SPEEDCON interlock
Pg screw connection	none
Housing material	Turned parts: copper zinc alloy (CuZn), die-cast parts: zinc (GD-Zn)
Material for screw connection	CuZn
Degree of protection (plugged in)	IP68/IP69K

Environmental and real-life conditions

Ambient conditions
Ambient temperature (operation)	-40 °C ... 115 °C (see derating curve)

Commercial data

Item number	1623719
Packing unit	1 pc
Minimum order quantity	1 pc
Note	Made to order (non-returnable)
Sales key	ABRCEM
Product key	ABRCEM
Catalog page	Page 128 (C-2-2019)
GTIN	4055626194875
Weight per piece (including packing)	609,7 g
Weight per piece (excluding packing)	528,109 g
Customs tariff number	85366990
Country of origin	DE

Classifications

Approvals

Approval Specification Data
	Nominal voltage U_N	Nominal current I_N	Cross section AWG
Power	600 V	35 A	8
Signal	500 V	4 A	16
Data	30 V	1 A	22

Approval Specification Data
	Nominal voltage U_N	Nominal current I_N	Cross section AWG
Power	600 V	28 A	10
Signal	500 V	4 A	1,5
Data	50 V	1 A	0,34

Approval Specification Data
	Nominal voltage U_N	Nominal current I_N	Cross section AWG
Power	600 V	70 A	10
Signal	500 V	4 A	1,5
Data	50 V	1 A	0,34

Environmental product compliance

EU RoHS
Fulfills EU RoHS substance requirements	Yes
Exemption	6(c)
China RoHS
Environment friendly use period (EFUP)	EFUP-50 An article-related China RoHS declaration table can be found in the download area for the respective article under "Manufacturer declaration". For all articles with EFUP-E, no China RoHS declaration table issued and required.
EU REACH SVHC
REACH candidate substance (CAS No.)	Lead (CAS: 7439-92-1)
SCIP	617411a4-b23e-4f54-ab10-702367754788

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

SB-8ESCD8AA700S - Device connector front mounting

1623719

Product details

ECLASS

ETIM

UNSPSC

cULus Recognized

cUL Recognized

UL Recognized

Compatible products

Your advantages

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

SB-8ESCD8AA700S - Device connector front mounting 1623719

Product details

ECLASS

ETIM

UNSPSC

Compatible products

SB-Z0001 - Metal protective cap 1623827

SB-Z0002 - Metal protective cap 1623828

PROT-M40-PW-OT-IP20 - Plastic protective cap 1577212

SB-10KS001 - Crimp contact 1623603

SB-10KS002 - Crimp contact 1623604

SB-10KS003 - Crimp contact 1623605

SB-10KS004 - Crimp contact 1623606

SB-36KS002 - Crimp contact 1623378

SB-36KS003 - Crimp contact 1623379

SB-36KS004 - Crimp contact 1623380

SB-36KS005 - Crimp contact 1623381

ST-10KS010 - Crimp contact 1618239

ST-10KS035 - Crimp contact 1618464

SF-08KS010 - Crimp contact 1621571

SM-Z0028 - Color coding 1620627

SM-Z0029 - Color coding 1620628

SM-Z0030 - Color coding 1620629

Your advantages

Frequently searched

SB-8ESCD8AA700S - Device connector front mounting

1623719