The D-SUB series, SUBCON-PLUS-PROFIB/... was specially designed for use in PROFIBUS systems up to 12 Mbps. Under field conditions, it allows convenient and fast connection of the incoming and outgoing bus cable. The terminating resistor is already integrated in all versions. It can be connected externally by means of a slide switch. At the same time, the outgoing bus segment is switched off. This makes it easy to start up segment by segment while incorrect terminations are avoided.
SUBCON-PLUS-PROFIB/90/IDC
-
D-SUB bus connector
2313672
D-SUB connector, 9-pos., pin, 90° cable outlet, bus system: PROFIBUS DP up to 12 Mbps, termination resistor can be switched on via slide switch, pin assignment: 3, 5, 6, 8; IDC terminal block connection
Product details
| Note on application | |
| Note on application | Only for industrial use |
| Product type | Data plug |
| MTTF | 6706 Years (SN 29500 standard, temperature 25°C, operating cycle 21%) |
| 1817 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%) | |
| 155 Years (SN 29500 standard, temperature 40°C, operating cycle 100%) | |
| Pin assignment | 3, 5, 6, 8 |
| Test voltage | 50 V |
| Maximum power dissipation for nominal condition | 0.025 W |
| Nominal voltage UN | 5 V |
| Nominal current IN | 100 mA |
| Tightening torque | ... 1.2 Nm |
| D-SUB connection | |
| Connection method | D-SUB connector |
| IDC terminal blocks | |
| Connection method | IDC fast connection |
| Conductor cross section, rigid min. | 0.32 mm² |
| Conductor cross section, rigid max. | 1 mm² |
| Conductor cross section flexible min. | 0.32 mm² |
| Conductor cross section flexible max. | 1 mm² |
| Single-wire/terminal point, rigid AWG min. | 22 |
| Single-wire/terminal point, rigid AWG max. | 18 |
| Min. AWG conductor cross section, flexible | 22 |
| Max. AWG conductor cross section, flexible | 18 |
| Bus system | PROFIBUS DP |
| Signal | PROFIBUS |
| Dimensional drawing |
|
| Width | 16.8 mm |
| Height | 34.8 mm |
| Length | 72 mm |
| External dimensions | |
| External diameter min. | 7.6 mm |
| External diameter max. | 8.4 mm |
| Material (Housing) | ABS (metal-plated) |
| External cable diameter | 7.6 mm ... 8.4 mm (Incoming bus line) |
| Mechanical data | |
| Insertion/withdrawal cycles | > 200 |
| Vibration resistance in accordance with EN 60068-2-6/IEC 60068-2-6 | Vibration (operation): 5g, 10...150 Hz, 2.5 h, in XYZ direction |
| Shock in accordance with EN 60068-2-27/IEC 60068-2-27 | Shock (operation): 15g, 11 ms period, half-sine shock pulse |
| Ambient conditions | |
| Degree of protection | IP40 |
| Ambient temperature (operation) | -20 °C ... 75 °C |
| Ambient temperature (storage/transport) | -25 °C ... 80 °C |
| Altitude | ≤ 5000 m (For restrictions, see the manufacturer's declaration for altitude operation) |
| Permissible humidity (operation) | 10 % ... 95 % (non-condensing) |
| Permissible humidity (storage/transport) | 5 % ... 95 % (non-condensing) |
| Corrosive gas test | |
| Identification | ISA-S71.04-1985 G3 Harsh Group A |
| Free from substances that could impair the application of coating | VDMA 24364:2018-05 |
UL Recognized
Approval ID: E238705CSA
Approval ID: 2437602
Your advantages
Suitable for all common Fast Connect PROFIBUS cables and RS-485 bus lines