PLC-SC-TR/INV
-
Switching amplifier
1395229
The inverter module with screw connection inverts the signals of ground switching NPN transistor outputs into positive switching PNP outputs, as well as signals from PNP into NPN switching signals.
Product details
| Notes on operation | The PLC-ATP separating plate should be installed for safe isolation between adjacent modules |
| Notes on operation | At least one functional insulation against adjacent modules is complied with in the support rail direction. If the application has higher requirements on the insulation (basic or reinforced insulation), then these must be realized through suitable measures (e. g., partition plates). |
| Notes on operation | This item is intended to be used exclusively as a supplied part for further processing by industry, trade, or other companies with expertise in the field of EMC. |
| Product type | Solid-state relay module |
| Product family | PLC-INTERFACE |
| Operating mode | 100% operating factor |
| Insulation characteristics | |
| Overvoltage category | II |
| Pollution degree | 2 |
| Rated insulation voltage | 50 V DC |
| Rated surge voltage | 0.5 kV |
| Supply | |
| Supply voltage UVcc | 24 V DC |
| Supply voltage range | 20 V DC ... 30 V DC |
| Typical input current at UN | 6 mA |
| Protective circuit | Surge protection |
| Surge voltage protection | > 33 V |
| Transmission frequency | 15 kHz |
| NPN | |
| Switching threshold "1" signal voltage | ≤ 5 V (at UVcc) |
| Switching threshold "0" signal, voltage | ≥ 15 V (at UVcc) |
| Min. voltage input signal | -2 V |
| Max. voltage input signal | 26 V |
| PNP | |
| Switching threshold "1" signal voltage | ≥ 19 V |
| Switching threshold "0" signal, voltage | ≤ 9 V |
| Min. voltage input signal | -2 V |
| Max. voltage input signal | 26 V |
| Continuous load current | 200 mA (OUT1/OUT2) |
| Leakage current | < 1 mA |
| Residual voltage | < 1 V |
| Transmission frequency | 15 kHz |
| Surge voltage protection | > 33 V |
| Protective circuit | Surge protection |
| Connection method | Screw connection |
| Stripping length | 8 mm |
| Screw thread | M3 |
| Conductor cross section rigid | 0.14 mm² ... 2.5 mm² |
| Conductor cross section flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross section flexible (2 conductors with same cross section) | 0.5 mm² ... 1 mm² (TWIN ferrule with plastic sleeve) |
| Conductor cross section AWG | 26 ... 14 |
| Tightening torque | 0.45 Nm ... 0.55 Nm (Usually these terminal blocks must be supported during conductor connection (held by one hand, supported on the housing)) |
| Width | 6.2 mm |
| Height | 80 mm |
| Depth | 94 mm |
| Ambient conditions | |
| Degree of protection | IP20 (Device) |
| Degree of protection (Installation location) | IP54 (Installation location) |
| Ambient temperature (operation) | -25 °C ... 60 °C |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Altitude | ≤ 2000 m |
| Standards/regulations | DIN EN 60664-1 |
| Mounting type | DIN rail mounting |
| Assembly note | in rows with zero spacing |
| Mounting position | any |
| Item number | 1395229 |
| Packing unit | 10 pc |
| Minimum order quantity | 1 pc |
| Product key | DK6213 |
| GTIN | 4063151778408 |
| Weight per piece (including packing) | 34.2 g |
| Weight per piece (excluding packing) | 26.95 g |
| Customs tariff number | 85365019 |
| Country of origin | DE |
ECLASS
| ECLASS-13.0 | 27371604 |
| ECLASS-15.0 | 27371604 |
ETIM
| ETIM 9.0 | EC001504 |
| EU RoHS | |
| Fulfills EU RoHS substance requirements | Yes |
| Exemption | 7(a), 7(c)-I |
| China RoHS | |
| Environment friendly use period (EFUP) |
EFUP-50
An article-related China RoHS declaration table can be found in the download area for the respective article under "Manufacturer declaration". For all articles with EFUP-E, no China RoHS declaration table issued and required.
|
| EU REACH SVHC | |
| REACH candidate substance (CAS No.) | Lead (CAS: 7439-92-1) |
| SCIP | 967fe662-a3f7-43ba-ac49-dc48e0164ab5 |
Phoenix Contact GmbH & Co. KG
Flachsmarktstraße 8, D-32825 Blomberg